|
TMS320C6416 DSP STARTER KIT |
PART NO:
TMDSDSK6416 |
The
TMS320C6416 DSP Starter Kit (DSK) developed jointly with Spectrum Digital
is a low-cost development platform designed to speed the development of
high performance applications based on TI´s TMS320C64x DSP generation. The
kit uses USB communications for true plug-and-play functionality. Both
experienced and novice designers can get started immediately with
innovative product designs with the DSK´s full featured Code Composer
Studio Tuning Edition v3.0 IDE .
Hardware
Features
• Texas Instruments TMS3206416 DSP
operating at 720 Mhz.
• Embedded USB JTAG controller with plug and
play, USB cable included
• TLV320AIC23 codec
• 2M x 64 on board
SDRAM
• 512K bytes of on board Flash ROM
• 3 expansion connectors
(Memory Interface, Peripheral Interface, and Host Port Interface)
• On
board IEEE 1149.1 JTAG connection for optional emulator debug
• Four
3.5 mm. audio jacks (microphone, line-in, speaker, line-out)
• 4 user
definable LEDs
• 4 position dip switch, user definable
• +5 Volt
operation only, power supply included
• Size: 8.25" x 4.5" (210 x 115
mm), 0.062" thick, 6 layers
• Compatible with Spectrum Digital's DSK
Wire Wrap Prototype Card
PRODUCT INCLUDES:
• C6416 1 GHz DSP Development Board with 512K Flash and 16MB SDRAM
• C6416 DSK Code Composer Studio™ v3.0 IDE
• Quick Start Guide
• Customer Support Guide
• USB Cable
• Universal Power Supply
• AC Power Cord(s)
OPERATING SYSTEM :
• WINDOWS
NT® 4.0 SERVICE PACK 4 OR HIGHER
• WINDOWS® 2000 SERVICE PACK 1
•
WINDOWS® ME
• WINDOWS® XP
HOST SYSTEM REQUIREMENT:
•
PENTIUM PC
• 630 MB HARD DISK FREE SPACE
• 128 MB RAM OR ABOVE
•
LOCAL CD DRIVE
• USB PORT
Top
TMS320C6713 DSP STARTER KIT |
PART NO:
TMDSDSK6713 |
The TMS320C6713 DSP Starter Kit (DSK) developed jointly with
Spectrum Digital is a low-cost development platform designed to speed the
development of high precision applications based on TI´s TMS320C6000
floating point DSP generation. The kit uses USB communications for true
plug-and-play functionality. Both experienced and novice designers can get
started immediately with innovative product designs with the DSK´s full
featured Code Composer Studio v3 IDE .
HARDWARE FEATURES
•
Texas Instrument's TMS320C6713 DSP operating at 225 Mhz.
• Embedded USB
JTAG controller with plug and play drivers, USB cable included
•
TLV320AIC codec
• 2M x 32 on board SDRAM
• 512K bytes of on board
Flash ROM
• 3 expansion connectors (Memory Interface, Peripheral
Interface, and Host Port Interface)
• On board IEEE 1149.1 JTAG
connection for optional emulator debug
• Four 3.5 mm. audio jacks
(microphone, line-in, speaker, and line out)
• 4 user definable
LEDs
• 4 position dip switch, user definable
• +5 Volt operation
only, power supply included
• Size: 8.25" x 4.5" (210 x 115 mm), 0.062"
thick, 6 layers
• Compatible with Spectrum Digital's DSK Wire Wrap
Prototype Card
PRODUCT
INCLUDES:
• C6713 DSP Development Board with
512K Flash and 8MB SDRAM
• C6713 DSK Code Composer Studio™ v3.0 IDE
• Quick Start Guide
• Technical Reference
• Customer Support
Guide
• USB Cable
• Universal Power Supply
• AC Power Cord(s)
OPERATING SYSTEM :
•
WINDOWS NT® 4.0 SERVICE PACK 4 OR HIGHER
• WINDOWS® 2000 SERVICE PACK
1
• WINDOWS® ME
• WINDOWS® XP
HOST SYSTEM REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK FREE SPACE
• 128
MB RAM OR ABOVE
• LOCAL CD DRIVE
• USB PORT
Top
TMS320C5416 DSP STARTER
KIT |
PART NO:
TMDSDSK5416 |
The TMS320C5416 DSP starter kit (DSK) is a low-cost development
platform designed to speed the development of power-efficient applications
based on TI's TMS320C54x DSPs. The kit, which provides new
performance-enhancing features such as USB communications and true
plug-and-play functionality, gives both experienced and novice designers
an easy way to get started immediately with innovative product
designs
.
HARDWARE FEATURES
• Texas Instrument's TMS320VC5416 DSP operating at 16-160 Mhz
• Embedded
USB JTAG controller with plug and play and play, USB cable included
•
Burr Brown PCM3002 stereo codec
• 64K words of on board RAM
• 256K
words of on board Flash ROM
• 3 Expansion connectors (Memory
Interface, Peripheral Interface, and Host Port Interface)
• On board
IEEE 1149.1 JTAG connection for optional emulator debug
• 4 user
definable LEDs
• 4 position dip switch, user definable
• +5 Volt
operation only, power supply included
• Size: 8.25" x 4.5" (210 x 115)
mm), 0.062" thick, 6 layers
• Compatible with Spectrum Digital's DSK
Wire Wrap Prototype Card
PRODUCT
INCLUDES:
• C5416 DSP Development Board
• C5416 DSK Code Composer Studio™ v3.0 IDE
• Quick Start Guide
• Technical Reference
• Customer Support Guide
• USB Cable
• Universal Power Supply
• AC Power Cord(s)
OPERATING SYSTEM :
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK FREE
SPACE
• 128 MB RAM OR ABOVE
• LOCAL CD DRIVE
• USB
PORT
Top
TMS320C5510 DSP STARTER
KIT |
PART NO:
TMDSDSK5510 |
The TMS320C5510TM DSP
Starter Kit (DSK) developed by Spectrum Digital is a low-cost development
platform designed to speed the development of power-efficient applications
based on TI´s TMS320C55x DSP generation. The kit, which provides new
performance-enhancing features such as power analysis tools and USB
communications for true plug-and-play
functionality.
• Texas Instrument's TMS320VC5510 DSP operating at 200 Mhz.
•
Embedded USB JTAG controller with plug and play drivers, USB cable
included
• TLV320AIC23 codec
• 8 Megabytes of on board SDRAM
•
512K bytes of on board Flash ROM
• 3 Expansion connectors (Memory
Interface, Peripheral Interface, and Host Port Interface)
• On board
IEEE 1149.1 JTAG connection for optional emulator debug
• Four 3.5 mm.
audio jacks (microphone, line-in, speaker, line-out)
• 4 user
definable LEDs
• 4 position disp switch, user definable
• +5 Volt
operation only, power supply included
• Size: 8.25" x 4.5" (210 x 115
mm), 0.062" thick, 6 layers
PRODUCT INCLUDES:
• C5510 DSP Development Board
• C5510 DSK Code Composer Studio™
v3.0 IDE
• Quick Start Guide
• Technical Reference
• USB Cable
• Universal Power Supply
• AC Power Cord(s)
OPERATING SYSTEM :
• WINDOWS NT®
4.0 SERVICE PACK 4 OR HIGHER
• WINDOWS® 2000 SERVICE PACK 1
•
WINDOWS® ME
• WINDOWS® XP
HOST SYSTEM REQUIREMENT:
•
PENTIUM PC
• 630 MB HARD DISK FREE SPACE
• 128 MB RAM OR ABOVE
•
LOCAL CD DRIVE
• USB PORT
Top
TMS320C2812 DSP STARTER
KIT |
PART NO: TMDSEZD2812 |
The F2812 eZdsp™ is a stand alone module that lets evaluators
examine certain characteristics of the F2812 digital signal processor
(DSP) to determine if this DSP meets their application requirements. This
module has a single chip parallel port to JTAG scan controller. Therefore
the module can be operated without additional development tools such as an
emulator. Furthermore, the module is an excellent platform to develop,
demonstrate, and run software for the F2812 processor
HARDWARE FEATURES
• TMS320F2812 Digital
Signal Processor
• 18K words RAM
• 128K words on chip Flash ROM
• 64K words on board RAM
• Expansion connectors
• Onboard
embedded IEEE 1149.1 JTAG controller
• 5 Volt only operation with
supplied adapter
• Onboard IEEE 1149.q JTAG emulation
Note: F2812 DSK Socket
version also available. Part No.TMDSEZDS2812
PRODUCT
INCLUDES:
• F2812 DSP Development Board
•
C2812DSK Code Composer Studio™
• Quick Start Guide
• Technical
Reference
• Customer Support Guide
• Parallel Port Cable
•
Universal Power Supply
• AC Power Cord(s)
OPERATING SYSTEM
:
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM
REQUIREMENT:
HARDWARE
FEATURES
• PENTIUM PC
• 630 MB HARD DISK FREE
SPACE
• 128 MD RAM OR ABOVE
• LOCAL CD DRIVE
• PARALLEL
PORT
Top
TMS320C2407 DSP STARTER
KIT |
PART NO:
TMDSEZD2407 |
The LF2407
eZdsp is a self contained, standalone development platform for the
TMS320LF2407 Fixed Point DSP. This unit has an embedded parallel port/IEEE
1149.1 scan controller enabling the user to perform true JTAG emulation.
Because the eZdsp operates off the parallel printer port no internal
adapter card is required. The eZdsp has 32K words of external program and
32K words of external data memory operating a zero wait states for easy
debugging. Power is provided via a supplied AC adapter.
HARDWARE FEATURES
• 510PP-Plus
emulation via FPGA
• 32K words program, 32K words data zero wait state
RAM
• C Compiler/Assembler/Linker
• Code Composer IDE, v4.12
(eZdsp specific). Not eligible for upgrades.
• AC adapter
•
Parallel port communication cable
• Standalone capability
•
Standard JTAG interface on board
• Users manual and documentation
• Direct interface to Spectrum Digital´s Digital Motor Controller
system
PRODUCT
INCLUDES:
• LF2407 DSP Development Board
•
LF2407 DSK Code Composer Studio™
• Quick Start Guide
• Technical
Reference
• Customer Support Guide
• Parallel Port Cable
•
Universal Power Supply
• AC Power Cord(s)
OPERATING SYSTEM
:
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK
FREE SPACE
• 128 MD RAM OR ABOVE
• LOCAL CD DRIVE
• PARALLEL PORT
Top
OMAP 5912 STARTER
KIT |
PART
NO:TMDSOCK5912 |
The
OMAP5912 Starter Kit (OSK) for Portable Data Terminals (PDT) is a low
cost, easy to use, convenient way of evaluating the features of the
OMAP5912 Processor in next generation PDT devices. The kit includes a
development board, and a collection of board and chip specific libraries
as well as a suite of development tools for Linux with an OMAP5912
specific Linux kernel. The kit allows users to get started on a portable
data terminal-based application and device development.
HARDWARE FEATURES
• ARM9 core operating
at 192 Mhz.
• DSP core operating at 192 Mhz.
• TLV320AIC23 Stereo
Codec
• 32 Mbyte DDR SDRAM
• 32 Mbyte Flash ROM
• 4 Expansion
connectors (bottom side)
• RS-232 Serial Port
• 10 MBPS Ethernet
port
• USB Host Port
• Compact flash connector
• On board IEEE
1149.1 JTAG connector for optional emulation
• +5 Volt operation
Software
Features
MontaVista LinuxTM
operating system and Linux Preview Kit for the Texas Instruments OMAP5912
processor - The Preview Kit reduces the amount of time you might otherwise
spend "test-driving" the operating system / hardware solution by providing
simple yet powerful demonstrations. With the MontaVista Linux Preview Kit,
developers are provided the opportunity to explore the building and
debugging process and evaluate real-world hardware performance. In
providing you this opportunity to validate the performance and
functionality of MontaVista Linux Professional Edition on your target
hardware, we will show you how MontaVista can empower and quicken your
development experience.
OPERATING SYSTEM
:
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK
FREE SPACE
• 128 MB RAM OR ABOVE
• LOCAL CD DRIVE
• PARALLEL PORT
Top
DM64x Digital Media Developer's Kit with NTSC
Camera |
PART NO:
TMDSDMK642 |
PRODUCT
DESCRIPTION:
Immediately start developing
multi-channel, multi-format digital media applications or other
future-ready high-performance video & imaging applications using the
DM64x Digital Media Developer’s Kit (DMDK). Loaded with starterware,
supported by award winning eXpressDSP™ host tools and target software and
offered at an exceptional price/performance ratio, the DMDK is a
comprehensive fully integrated development platform and an easy-to-use,
robust tool suite. Leveraging the high performance TMS320C64x DSP core,
this development platform supports TI’s TMS320DM642, DM641 & DM640
digital media processors.
Two types of users are
targeted to jump-start your application development:
• Experienced with
programmable DSP (either TI or other) and want to add multimedia
functionality
to an existing or new product/system
• Experienced in
video with a background in analog or fixed function hardwired
chipsets/ASIC/SOC
with minimum experience in writing target DSP software,
and who want to use a fully software
programmable DSP to increase the
performance, flexibility and functionality of a video & imaging
system.
PRODUCT
INCLUDES:
• DM642 EVM Baseboard
• Code
Composer Studio v3.0 for the DM64x generation of processors only
•
DSP/BIOS Real Time Kernel
• Advanced PCI Emulator: XDS560 PCI
•
DM642 EVM CD (contents described above)
• NTSC or PAL Camera
•
Video Cables (2 RCA & 1 S-Video)
• DM642 EVM Quick Start Guide
• DM642 EVM Technical Reference
• 5V/5A Power Supply
•
Multilingual Regulatory Compliance Statement
OPERATING SYSTEM
:
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK FREE SPACE
• 128 MB RAM OR
ABOVE
• LOCAL CD DRIVE
• PCI EMULATOR & USB PORT
Top
Fingerprint Authentication Development
Tool (FADT) |
|
PRODUCT DESCRIPTION:
The
Fingerprint Authentication Development Tool (FADT) provides developers
with an easy-to-use, cost-effective way to evaluate and develop
fingerprint authentication systems and products based on TI digital signal
processors (DSP).
HARDWARE
FEATURES
• FPC1010 fingerprint sensor from
Fingerprint Cards AB
• Compatible with TMS320C5510, TMS320C6711 and
TMS320C6713 DSP Starter Kits and
TMS320C5509 EVM from Spectrum Digital
(attaches via expansion connector)
• LEDs to display enrollment and
verification function status
• Sensor guide to help in correct
fingerprint placement on the sensor
• Slide switch to allow control of
enroll and verify functions in a completely embedded environment
(without
GUI on PC)
Software Features
Standard
•
Sensor drivers for fingerprint image capture on both TMS320C55x and
TMS320C67x DSP
• Sensor drivers image capture demo for Code Composer
Studio™ Development Tool (CCStudio)
Special evaluation software (for
TMS320C5510 and TMS320C6713 DSP Starter Kits)
• Evaluation copy of
Fingerprint Cards AB "Distinct Area Detection" fingerprint verification
algorithm
for TMS320C5510 and TMS320C6713 DSP Starter Kits
Fingerprint
Cards FPCore demo (GUI for PC) for host side user interface using the Real
Time Data
Exchange2 (RTDX) communication protocol
PRODUCT
INCLUDES:
• Daughter Card (expansion board) with
Fingerprint Cards FPC1010 sensor
• "Fingerprint development support
for TI DSPs" software CD
• FPC1010 Sensor driver source code for C55x
and C67x DSP generations
• Sensor driver image capture demo
•
FPCore fingerprint verification demo Copies of license agreements
•
Hardware and software user guides
• Quick Start Guide
OPERATING SYSTEM :
• WINDOWS NT®
4.0 SERVICE PACK 4 OR HIGHER
• WINDOWS® 2000 SERVICE PACK 1
•
WINDOWS® ME
• WINDOWS® XP
HOST
SYSTEM REQUIREMENT:
• PENTIUM PC
• 630
MB HARD DISK FREE SPACE
• 128 MB RAM OR ABOVE
• LOCAL CD DRIVE
•
PARALLEL PORT OR USB PORT
Top
DM642 EVALUATION MODULE |
PART NO:
TMDSEVM642 |
PRODUCT
DESCRIPTION:
The DM642 Evaluation
Module (EVM) is a low-cost high performance video & imaging
development platform designed to jump-start application development and
evaluation of multi-channel, multi-format digital and other future proof
applications. Leveraging the high performance TMS320C64x DSP core, this
development platform supports TI’s TMS320DM642, DM641 & DM640 digital
media processors.
Developed in
conjunction with Spectrum Digital, this PCI form factor EVM includes the
necessary components to enable you to:
• Start application
software development immediately
• Understand DSP functionality for
video experts
• Build video, audio & internet streaming
functionality into existing designs
• Simplify overall system design
• Differentiate your product with cutting edge software
• Design
for flexibility to respond to evolving standards
PRODUCT
INCLUDES:
• DM642 EVM Baseboard
• DM642 EVM
CD (contents described above)
• DM642 EVM Quick Start Guide
•
DM642 EVM technical reference
• 5V/5A Power Supply
OPERATING SYSTEM
:
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK
FREE SPACE
• 128 MD RAM OR ABOVE
• LOCAL CD DRIVE
• USB
PORT
Top
LF2407 EVALUATION
MODULE |
PART NO:
TMDS3P701016A |
PRODUCT DESCRIPTION:
The
TMS320LF2407A Evaluation Module kit gives designers a complete and cost
effective way to take their designs from concept to production. The kit is
the easiest way to fully evaluate and begin developing code for embedded
applications. The LF2407A EVM builds on TI's industry-leading array of
development tools that allow designers to take full advantage of the
benefits of DSP-based systems.
HARDWARE
FEATURES
• Texas Instruments TMS320LF2407 Digital
Signal Processor
• 64K words program memory, zero wait states
•
64K words data memory, zero wait states
• 32K words Flash ROM in
program space
• DAC7625 DAC, (4 channels, 12 bits)
• Standard JTAG
interface onboard
• Stand-alone operation for easy debug access
•
Expansion connectors for add-on accessories
• On board UART and CAN
interface for boot loading
Software
Features
• Compatible with
TI's Code Composer Studio IDE
• Supports TI 'C'
compiler/assembler/linker
• Compatible with Spectrum Digital's
emulation tools:
• XDS510PP Plues JTAG Emulator
• Compatible with
Spectrum Digital and TI flash programming utility
PRODUCT INCLUDES:
• LF2407 EVM
Baseboard
• Code Composer Studio
• LF2407 EVM Quick Start Guide
• XDS 510PP+ Emulator
• 5V/5A Power Supply
OPERATING
SYSTEM :
• WINDOWS NT® 4.0
SERVICE PACK 4 OR HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS®
ME
• WINDOWS® XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK
FREE SPACE
• 128 MB RAM OR ABOVE
• LOCAL CD DRIVE
• PARALLEL
PORT
Top
F2812 EVALUATION
BUNDLE |
PART NO:
TMDSEVP2812 |
PRODUCT
DESCRIPTION:
The F2812 Development Bundle gives
designers a complete and cost effective way to take their design from
concept to production. The bundle provides capabilities to evaluate
characteristics of the TMS320F2812 DSP and develop, demonstrate, and run
software for the processor.
The XDS510 emulator is
tightly integrated with the Code Composer Studio™ debugger interface,
making all of TI´s real time emulation control and visualization
capabilities available to the developer. These range from single-stepping,
and register visibility, to software and hardware breakpoints, and
cycle-accurate benchmarking. All of this is supported without requiring a
debug monitor. Custom target boards for all TI DSPs can be debugged using
the XDS510 PP+ emulator included in this development bundle, through a
standard 14-pin JTAG header
PRODUCT
INCLUDES:
• F2812 DSP Starter Kit
• Code
Composer Studio
• F2812 DSK Quick Start Guide
• XDS 510PP+
Emulator
• 5V/5A Power Supply
OPERATING SYSTEM
:
• WINDOWS NT® 4.0 SERVICE PACK 4 OR
HIGHER
• WINDOWS® 2000 SERVICE PACK 1
• WINDOWS® ME
• WINDOWS®
XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK
FREE SPACE
• 128 MB RAM OR ABOVE
• LOCAL CD DRIVE
• PARALLEL PORT
Top
XDS510PP PLUS JTAG Scan Path Emulator
Pod |
|
PRODUCT
DESCRIPTION:
HARDWARE
FEATURES
• Supports Texas Instruments
Digital Signal Processors and Microcontrollers with JTAG interface
•
Compatible with XDS510 from Texas Instruments
• Operates with parallel
port on PC or laptop, no internal adapter required
• Supports
bi-directional, ECP, and EPP transfers
• Compatible with +3.3V or +5V
processors
• Powered by target or supplied adapter
• Compatible
with SPI110 Opto Pod
• Compatible with 4 Channel JTAG
Expander
Software
Features
• Compatible with
Code Composer Studio from Texas Instruments
• Compatible with Win 98
ME, NT, 2000, XP
• Operates with "SDFlash" Programming Utility from
Spectrum Digital
• Compatible with Programming utilities developed by
Texas Instruments
PRODUCT
INCLUDES:
• XDS510PP PLUS JTAG Emulator
• +5
Volt power supply
• Parallel port cable
• CD-ROM with drivers
• Installation Instructions
COMPATIBLE
PRODUCTS
• C2xx, C24x, F240x, F2812, VC33, C4x,
C5x, C54xx, C55xx, C6xxx, C64xx, TMS470, OMAP
Top
XDS510 USB JTAG Scan Path Emulator
Pod |
|
PRODUCT
DESCRIPTION:
HARDWARE
FEATURES
• Supports Texas Instruments
Digital Signal Processors and Microcontrollers
• Compatible with XDS510
from Texas Instruments
• Operates off PC/laptop USB port, no internal
adapter required
• USB bus powered, no power supply required
•
Supports USB 1.x and USB 2.0 (full speed)
• Advanced emulation
controller provides high performance
• Compatible with +3.3V or +5V
processors
• One LED provides operational status
Software
Features
• Compatible with Code Composer Studio
from Texas Instruments
• Compatible with Win 98 ME, NT, 2000, XP
•
Operates with "SDFlash" Programming Utility from Spectrum Digital
•
Compatible with Programming utilities developed by Texas Instruments
PRODUCT
INCLUDES:
• XDS510PP PLUS JTAG Emulator
• +5
Volt power supply
• Parallel port cable
• CD-ROM with drivers
• Installation Instructions
COMPATIBLE
PRODUCTS
• F240x, F28xx, C54xx, C55xx, C6xxx, TMS470 ARM9, OMAP
Top
XDS560 PCI-bus JTAG Scan-Based
Emulator |
|
PRODUCT
DESCRIPTION:
The XDS560 emulator is a PCI-based next-generation emulation
controller that supports high-speed RTDX on an enabled processor for
real-time data rates of over 2 MB/second. It provides an unparalleled
level of real-time visibility into an executing application to assist
developers in debugging real-time systems. The XDS560 can achieve code
download speeds of up to 500 Kbytes per second improving start-up times
for larger applications and thus speeding development. The XDS560 also
enables real-time non-intrusive Advanced Event Triggering capabilities,
including event sequence detection, extended benchmarking capabilities,
and program range breakpoints. The XDS560 is compatible with existing
XDS510-class emulators, and uses the identical 14-pin JTAG header
connector used by the XDS510 to preserve investments made in software and
target boards
PRODUCT
INCLUDES:
• XDS560 JTAG Emulator
• CD-ROM with drivers
• Installation
Instructions
COMPATIBLE
PRODUCTS
• F240x, F28xx, C54xx, C55xx, C6xxx, TMS470 ARM9, OMAP
PRODUCTS NOT
SUPPORTED
• 'C2x, 'C20x, 'C3x, 'C4x, 'C5x, 'C8x
These processor families
will not be supported by the XDS560 JTAG emulator
Top
TMS320VC33 DSP STARTER KIT |
PART NO:
TMDSEVP2812 |
PRODUCT
DESCRIPTION:
The TMS320VC33 DSK is built using a state of the art low power and
low cost 150 MegaFlop TMS320VC33. The board is further supported by a
48Khz stereo 20 bit codec with 2 on-board microphones, external SRAM,
external FeRAM boot flash and CPLD logic. The new software applications
and demos run under all Windows platforms (older C31 DSK applications are
supported but Win9x only). Applications can also now be created in less
time using the included TI-COFF optimizing C compiler.
HARDWARE
FEATURES
• TMS320VC33 Digital Signal Processor (DSP)operating at 60 MHz from
Texas Instruments
• Embedded IEEE 1149.1 JTAG scan controller
•
Interface to host PC via parallel port for debug and communications
•
TLC320AD50C Sigma-Delta Codec with input and output jacks
• 2
expansion connectors for custom user logic (data, address, I/O, McBSPs)
• Stand alone capability
• +5 volt only power, AC adapter included
• Communication cable included
Software Features
• eZdsp VC33
Code Composer (includes C3x 'C' Compiler, Assembler, Linker, and debugger)
from Texas Instruments
PRODUCT
INCLUDES:
• eZdsp VC33 target board
• Parallel port cable
• CR-ROM
with eZdsp VC33 Code Composer
• CD-ROM with Code Composer driver
•
CD with documentation including reference manual
OPERATING SYSTEM
:
•
WINDOWS NT® 4.0 SERVICE PACK 4 OR HIGHER
• WINDOWS® 2000 SERVICE PACK
1
• WINDOWS® ME
• WINDOWS® XP
HOST SYSTEM
REQUIREMENT:
• PENTIUM PC
• 630 MB HARD DISK FREE SPACE
• 128 MB RAM OR
ABOVE
• LOCAL CD DRIVE
• USB PORT
Top
Description
The DSKeye is a low cost Image
developer kit for Texas Instruments DSK boards including a hardware TCP/IP
interface and configurable expansion using the Santa Cruz interface. At
the heart of the DSKeye is a Cyclone II FPGA, the latest device from
ALTERA. This device bridges the camera to the DSP's external bus allowing
efficient image transfers to main memory with little DSP overhead. It is
also used to implement user-defined interfaces through the ALTERA, Santa
Cruz connectors.
A growing number of Santa Cruz boards are available
covering VGA, USB etc and there is also a prototyping board allowing true
user definable interfaces. Visit the ALTERA website for more information
on the Santa Cruz specification. The embedded TCP/IP Ethernet adapter is
based on the WizNET W3100A device. The interface contains a hardware
TCP/IP stack removing any DSP processing overhead and comes royalty free.
The device handles TCP, UDP, IP, ICMP, ARP/RARP and raw MAC and DLC
protocols with extended protocols such as DHCP and SMTP, etc easily
accommodate in software. The Wiznet API has been integrated into the
DSP/BIOS operating system to ease development. Inclusion of TCP/IP enables
the DSKeye to be used as the basis of net attached smart camera and VOIP
projects.
The FLASH programming functionality of the DSK board allows
stand-alone applications to be implemented at a fraction of the cost
currently available on the smart camera market. By using the DSK's onboard
digital and analogue i/o a complete high-performance, comprehensive
machine vision controller can be built and installed. Many customer
applications exploit the power of the 750Mhz, 64Bit C6416DSK producing
6,000MIPS at approximately 1.5Watts (The Pentium 4 yields approximately
1,700MIPS while consuming approx 85 Watts). The DSKs are bundled with the
complete TI optimizing compiler, IDE and DSP/BIOS real-time operating
system.
The camera head can be mounted horizontally, vertically or
remotely on a short ribbon cable. The card is easily programmed and is
shipped with software examples and all FPGA programming
files
Applications
• Machine vision
• Video phone
• Remote image sensing
• Surveillance systems
• Biometrics
• Image recognition, filtering and compression
• Video streaming
• Stand-alone vision systems
• Net-connect smart camera
• VOIP
projects. |
